background image

www.usaprocom.com

200047-01A

18

 WARNING: You must operate 

this heater with the door closed 

and in the locked position. Make 

sure screen is installed before 

running heater.
NOTICE: During initial operation of 

new heater, burning logs will give 

off a paper-burning smell. Orange 

flame will also be present. Open 

damper or window to vent smell. 

This will only last a few hours.

1.  STOP! Read the safety information above.

2.  Make sure equipment shutoff valve is fully 

open.

3.  Push  in  control  knob  slightly  and  turn 

clockwise 

 to the OFF position.

4.  Wait five (5) minutes to clear out any gas. 

Then smell for gas around heater and near 

the floor. If you smell gas, STOP! Follow 

"B" in the safety information above. If you 

do not smell gas, go to the next step.

5.  Turn control knob counterclockwise 

 

to  the  PILOT  position.  Press  in  control 

knob for five (5) seconds.

 

Note: The first time that the heater is oper-

ated after connecting the gas supply, the 

control knob should be pressed for about 

thirty (30) seconds. This will allow air to 

bleed from the gas system. If pilot does not 

stay lit, refer to Troubleshooting, pages 26 

though 28. Also contact a qualified service 

technician or gas supplier for repairs. Until 

repairs are made, light pilot with match.

• If  control  knob  does  not  pop  up  when 

released,  contact  a  qualified  service 

technician or gas supplier for repairs.

6.  With  control  knob  pressed  in,  push 

down  and  release  ignitor  button.  This 

will  light  pilot.  The  pilot  is  attached  to 

the  rear  of  the  burner.  If  needed,  keep 

pressing  ignitor  button  until  pilot  lights.

 

Note: If pilot does not stay lit, refer to 

Troubleshooting, page 26. Also contact a 

qualified service technician or gas supplier 

for repairs. Until repairs are made, light 

pilot with match. To light pilot with match, 

see Manual Lighting Procedure

, page 19

.

7.  Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds, 

release control knob.

 

Note: If pilot goes out, repeat steps 3 

through 7. This heater has a safety inter-

lock system. Wait one (1) minute before 

lighting pilot again.

8.  Turn control knob counterclockwise 

 

to  the  desired  heating  level. The  main 

burner  should  light.  Set  control  knob  to 

any heat level between HI (5) and LO (1).

 

Note: Please wait one minute after shut-

ting off fireplace to allow the control valve 

to reset before starting again.

 CAUTION: Do not try to ad-

just heating levels by using the 

equipment shutoff valve.

 WARNING: If input gas 

type is NG, make sure NG pilot 

burner ignites. If input gas type 

is LP, make sure LP pilot burner 

ignites.

MODEL PCSD25T

LIGHTING INSTRUCTIONS

Ignitor 

Button

Control Knob

Figure 18 - Ignitor Button and Control 

Knob Locations

OPERATION

Содержание pcnsd25rt

































Отзывы: