Procom pcnsd25rt Скачать руководство пользователя страница 11

www.usaprocom.com

11

200047-01A

This appliance is factory 

preset for propane/LP gas. 

No changes are required for 

connecting to propane/LP.

 Only 

a  qualified  installer  or  service 

technician can perform gas selec-

tion and connecting to gas supply.

 CAUTION: Two gas line in-

stallations at the same time are 

prohibited.  The  access  plate 

to the simple switching means 

shall  not  be  opened  while  the 

heater is in operation.

 CAUTION: To avoid gas 

leakage at the inlet of regulator, 

a  qualified  installer  or  service 

technician must use supplied 

hex plug with sealant.

 WARNING: Do not attempt to 

access or change the setting of 

the fuel selection means.

Access to and adjustment of the fuel selection 

means must only be performed by a qualified 

service person when connecting this appliance to 

a specified fuel supply at the time of installation.
Change of the selector setting to other than 

the fuel type specified at the time of installa-

tion could damage this appliance and render 

it inoperable.
The installer shall replace the access cover 

before completing the installation and operat-

ing this appliance.

For changing from propane to 

natural gas supply:

1.  Remove 1 screw from gas selector cover 

plate (see Figure 5). Rotate to expose fuel 

selector device.

2.  For NATURAL GAS, press in knob using a 

flat screwdriver with a blade with thickness 

of a quarter and turn knob clockwise 

 

until the knob locks into the NG position 

(see Figure 5). Fuel selection device must 

be locked in the NG position. Do not oper-

ate heater between locked positions!

NG

Gas Inlet

Gas esté

INLET GAS PRESSURE

MAX 1/2 PSIG (3.5KPa)

Gas Select

Selector de gas

LP

NG

LP

NG

Gas Inlet

Gas esté

INLET GAS PRESSURE

MAX 1/2 PSIG (3.5KPa)

Gas Select

Selector de gas

LP

NG

LP

INSTALLATION

Figure 5 - Settings for Natural Gas 

Selection

GAS SELECTION

3.  Replace cover over fuel selection device 

and reinstall screws.

4.  Remove hex plug (with wrench provided) 

from  natural  gas  inlet  of  regulator  (see 

Figure 5). Install hex plug into LP inlet of 

regulator. Install gas line into NG inlet of 

regulator.  Use  thread  sealant  to  assure 

there are no leaks.

Fuel 

Selector 

Knob

Fuel 

Selector 

Knob

Hex Plug

Hex Plug

Figure 6 - Settings for Propane/LP Gas 

Selection

Gas Connection 

Fitting

Gas Connection 

Fitting

Back of Stove

Back of Stove

For changing from natural gas 

supply to propane supply:

1.  Remove 1 screw from gas selector cover 

plate (see Figure 6). Rotate to expose fuel 

selector device

2.  For PROPANE GAS, press in knob using a 

flat screwdriver with a blade the thickness 

of a quarter and turn knob counterclock-

wise 

 until the knob locks into the 

LP position (see Figure 6). Fuel selection 

device must be locked in the LP position. 

Do  not  operate  heater  between  locked 

positions.

3.  Replace cover over fuel selection device 

and reinstall screws.

4.  Remove hex plug (with wrench provided) 

from  propane/LP  gas  inlet  of  regulator 

(see Figure 6). Install hex plug into NG 

inlet of regulator. Install gas line into LP 

inlet of regulator. Use thread sealant to 

assure there are no leaks.

Содержание pcnsd25rt

































Отзывы: