Probasics Wheelchair XP6500 страница 50 Скачать руководство пользователя

Страница: 50 / 64

Part No. 1123839

SECTION 11—BATTERIES

4. Place rear battery box onto the battery

tray and connect the rear battery box to

the front battery box.

5. Connect the front battery box to the

controller.

WARNING

The battery box retaining strap MUST

be fastened securely and adjusted prop-

erly to hold battery boxes in place

before using the wheelchair.

6. Connect the battery box retaining strap

clip together and adjust if necessary.

FIGURE 11.3

Removing/Installing the

Battery Boxes

Installing/Removing Battery Tray

NOTE: For this procedure, refer to FIGURE 11.4.
NOTE: To remove the battery tray from the wheelchair, reverse the following procedure.

1. Attach the key slot bracket located at the front of the battery tray over the crossbrace

bolt bushing under the seat upholstery of the wheelchair.

2. Attach the hanger brackets to the wheelchair frame.

FIGURE 11.4

Installing/Removing Battery Tray

Front Battery Box

Connectors

Rear Battery

Box

Connector

Rear

Battery

Box

Front

Battery

Box

Battery

Tray

Retaining

Strap

To Controller

Retaining Strap Clip

Crossbrace Bolt Bushing

Wheelchair Frame

Key Slot Bracket

Battery Tray

Hanger

Bracket

Содержание Wheelchair XP6500

































































Результаты поиска

Содержание Wheelchair XP6500

Отзывы:

Похожие инструкции для Wheelchair XP6500

Бренды по названию

Популярные бренды

Probasics Wheelchair XP6500, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Wheelchair XP6500

Отзывы:

Похожие инструкции для Wheelchair XP6500

Бренды по названию

Популярные бренды