Probasics Wheelchair XP6500 страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 64

background image

SECTION 6—FRONT RIGGINGS

Part No. 1123839

33

SECTION 6—FRONT RIGGINGS

WARNING

After ANY adjustments, repair or service and before use, make sure that all

attaching hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service verify that On/Off

switch on the joystick is in the Off position.

Installing/Removing/Using the Footrest/Legrest

NOTE: For this procedure, refer to FIGURE 6.1.
NOTE: This procedure applies to the swingaway footrest and elevating legrest.

Installing

1. Turn the swingaway footrest assembly to the side (open footplate is perpendicular to

wheelchair).

2. Install the hinge plates on the swingaway footrest assembly onto the hinge pins on the

wheelchair frame.

3. Push the swingaway footrest assembly towards the inside of the wheelchair until it

locks into place.

NOTE: The footplate will be on the inside of the wheelchair when locked in place.

4. Repeat this procedure for the other footrest assembly.

FIGURE 6.1

Installing/Removing/Using the Footrest/Legrest

Hinge

Pins

Hinge

Plates

Footrest

Release Lever

Swingaway

Footrest

Assembly

Footplate

«
...
31
32
33
34
35
...
»

Содержание Wheelchair XP6500

































































Отзывы:

Нет отзывов

Похожие инструкции для Wheelchair XP6500

Бренд: Otto Bock Страницы: 8

Бренд: progeo Страницы: 48

Бренд: Feather Страницы: 11

Бренд: Invacare Страницы: 84

Бренд: Lifeline Страницы: 5

Бренд: EZee Life Страницы: 5

Бренд: EZee Life Страницы: 8

Бренд: EZee Life Страницы: 6

ROHO Hybrid Elite 1RHE1414C-SR

Бренд: Permobil Страницы: 128

Бренд: Degonda-Rehab SA Страницы: 48

Бренд: RMS Страницы: 20

Бренд: RMS Страницы: 20

Бренд: Safer Locks Страницы: 25

Бренд: TransMotion Medical Страницы: 30

LI2161.121 Series

Бренд: Handicare Страницы: 12

Sopur Ti Titanium

Бренд: Quickie Страницы: 216

Бренд: Sunrise Medical Страницы: 2

Бренд: Sunrise Medical Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды