Probasics Wheelchair XP6500 Скачать руководство пользователя

Страница: 9 / 64

LABEL LOCATIONS

Part No. 1123839

LABEL LOCATIONS

Crossmember

Lower Frame

Tube

WARNING

DO NOT OPERATE WITHOUT

THE ANTI-TIP TUBES

INSTALLED.

REV. 5/98

P/N 60106X144

Refer to Owner's Manual
for proper anti-tipper
setting.

1085379

WARNING

IMPORTANT NOTICE

The wheel locks on this wheelchair have been

pre-set at the factory to comply with the

Veterans Administration functional Standard

8320.01 of the Federal Register, paragraph

3.2.4.5.3. If these wheel locks do not meet

your needs, follow instructions below.

CAUTION

Any wheel lock adjustments should embed

wheel lock shoe at least 1/8" into tire when

locked (3/16" on pneumatic tires).

INSTRUCTIONS FOR WHEEL

LOCK ADJUSTMENTS

1.Loosen wheel lock mounting fastener,

which runs through mounting bracket and

frame.

2.Slide clamp toward rear wheel until wheel

lock shoe is embedded into tire material at

least 1/8" when handle is engaged to the

lock position (3/16" for pneumatic tires).

3.Tighten mounting fastener to secure

mounting bracket in desired location and

recheck lock shoe embedding.

4.Inspect for correct locking action BEFORE

actual use.

00078X021-0394

Содержание Wheelchair XP6500

































































Результаты поиска

Содержание Wheelchair XP6500

Отзывы:

Похожие инструкции для Wheelchair XP6500

Бренды по названию

Популярные бренды

Probasics Wheelchair XP6500, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Wheelchair XP6500

Отзывы:

Похожие инструкции для Wheelchair XP6500

Бренды по названию

Популярные бренды