Probasics Wheelchair XP6500 Скачать руководство пользователя

Страница: 45 / 64

SECTION 10—CASTERS

Part No. 1123839

SECTION 10—CASTERS

WARNING

After ANY adjustments, repair or service and before use, make sure that all

attaching hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service verify that On/Off

switch on the joystick is in the Off position.

CAUTION

As with any vehicle, the wheels, casters and tires should be checked periodically for

cracks and wear and should be replaced.

Adjusting Forks

NOTE: For this procedure, refer to FIGURE 10.1.

1. Remove the dust cover from the caster headtube.
2. To properly tighten caster journal system and guard against flutter, perform the

following check:
A. Remove battery boxes and battery tray from wheelchair. Refer to

Removing/Installing the Battery Boxes on page 49 and Installing/Removing

Battery Tray on page 50.

B. Tip back the wheelchair to floor.
C. Pivot both forks and casters to top of their arc simultaneously.
D. Let casters drop to bottom of arc

(wheels should swing once to

one-side, then immediately rest in a

straight downward position).

E. Adjust locknuts according to

freedom of caster swing.

3. Test wheelchair for maneuverability.
4. Readjust locknuts if necessary, and

repeat STEPS 1-3 until correct.

5. Snap dust cover into the caster

headtube.

FIGURE 10.1

Adjusting Forks

Dust Cover

Locknut

Nylon

Washer

Caster

Headtube

Fork

Caster

Содержание Wheelchair XP6500

































































Результаты поиска

Содержание Wheelchair XP6500

Отзывы:

Похожие инструкции для Wheelchair XP6500

Бренды по названию

Популярные бренды

Probasics Wheelchair XP6500, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Wheelchair XP6500

Отзывы:

Похожие инструкции для Wheelchair XP6500

Бренды по названию

Популярные бренды