Primus FF10 Скачать руководство пользователя страница 64

Страница: 64 / 136

PROGRAMMING MANUAL

100962 G PUBLICATION DATE 24 JUN 2008.DOC

THE FLUSH SEQUENCE

Only for Top Soap Hopper washing machines.

No water level can be programmed as the water will raise and escape by the overflow hole.

No inlets can be programmed as only cold water from inlet 6 is used.

No supplies can be programmed.

•

The suggested drum speed value depends on the machine

type.

•

Check the corresponding table paragraph 3.4.

•

The drum speed value can only be programmed within

certain limits.

•

Insert the desired speed value. Press the

ENTER

button for

confirmation.

•

The wash motor ON time can be programmed between 0 and

99 seconds.

•

The wash motor OFF time can be programmed between 3

and 99 seconds.

•

The suggested default values can be changed in the

Initialisation menu.

•

Standard wash motor ON time of 12 seconds and a wash

motor OFF time of 3 seconds is recommended for normal

wash. A wash motor ON time of 3 seconds and a wash motor

OFF time of 12 seconds is recommended for a gentle wash

(woolens).

•

Insert the desired ON – OFF times. Press the ENTER button

for confirmation.

•

The Flush Sequence can be programmed between 0 and

99 minutes in steps of 0.5 minutes.

•

The Default time is 10.0 Minutes.

•

Programming a time of 0 minutes : the Flush will not be

functional (cfr No Wash)

•

Insert the desired Flush Sequence time. Press the ENTER

button for confirmation.

Prewash

| Wash | Cooldown | Rinse |

Final Rinse

| Soak |

Flush

| Spray | No wash

P:Pr XX Step XX

RPM : _ _

P:Pr XX Step XX

Time : 10.0 Min

P:Pr XX Step XX

On Time : _ _ Sec

P:Pr XX Step XX

Off Time : _ _ Sec

Содержание FF10









































































































































Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды

Primus FF10, Руководство по программированию

Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды