Primus FF10 Скачать руководство пользователя страница 35

Страница: 35 / 136

100962 G PUBLICATION DATE 24 JUN 2008.DOC

PROGRAMMING MANUAL

•

Some washing machines function with external Liquid soap

supplies and others do not.

•

If external liquid soap supplies are connected to the washing

machine, the selection must be Yes.

•

If No is selected, then No external liquid soap supplies can

be programmed at the Program menu.

•

Yes : Liquid Supply Signals enabled.

No : Liquid Supply Signals disabled.

•

Confirm by pressing the ENTER button.

•

Soap Supply signals will only be started when the

pre-set water level has been reached.

•

Default value :

- 0 units for top soap Dispensing machines.

- 10 units for front soap Dispensing machines.

•

The value can be programmed between 0 and the minimum

programmable water level. See water consumption table.

•

Confirm by pressing the ENTER button.

Front soap hopper machines Only.

•

The liquid soaps supplying the manifold can be flushed

by an extra water inlet that is mounted on the manifold of the

soap dispensing system.

This extra water supply is called : LS-Flush

(Liquid Soap-Flush)

•

Both menus are only visible when in the configuration menu

“Liquid Supply Signals” is set Yes.

•

The time to flush, before the liquid supplies are switched On,

can be set to: 0-15 seconds.

•

The time to flush, after the liquid supplies are switched Off,

can be set to: 0-99 seconds.

•

When both time settings are 0 seconds then the manifold

will not flush water at all while liquid soap supply is pumped

into the manifold.

•

1 second Pre-Time and 5 seconds After-Time are the

default values. (FF120=10”).

•

Confirm by pressing the ENTER button.

•

Press the ARROW LEFT or RIGHT button to

select Celsius or Fahrenheit, depending if you prefer that the

temperature is displayed in degrees Celsius or degrees

Fahrenheit.

C:Liquid Supply

Signals: No

C:Temperature:

Celcius

C:LS-Flush

After-time : 05 Sec

C:LS-Flush

Pre-time : 01 Sec

C:Minimum Level

Start Supply : 0

Содержание FF10









































































































































Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды

Primus FF10, Руководство по программированию

Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды