Primus FF10 Скачать руководство пользователя страница 100

Страница: 100 / 136

PROGRAMMING MANUAL

100962 G PUBLICATION DATE 24 JUN 2008.DOC

•

Press the ARROW DOWN button to see

message by message and to leave the Error message menu.

•

If no messages are displayed, this means that no Errors have

occurred.

•

If you don‘t want to erase the Fault messages,

press the ARROW DOWN button.

•

Press the YES and ENTER button if you want to

erase the Error messages.

•

If you don‘t want to see the Fault statistics,

press the ARROW DOWN button.

•

If you want to see the Fault statistics, press the

ENTER button.

•

The Fault Statistics are an accumulation of Errors messages

that have appeared over a long period.

•

The Statistics can be reset at the Service Menu, by a Reset

of the Cycle counter.

•

With this information the technician has an indication on

which parts an intervention will be needed.

The List with Statistics.

No Drain

: E1 + E2 + E37

Door Switch

: E6 + E7 + E8 + E9

Bimetal / Spring

: E10 + E56

No Fill

: E11 + E40

No Heating

: E13 + E14

Thermic

: E18 + E19 + E20 + E36

Temp Sensor

: E25

Level Sensor

: E24

Mitsubishi Alarm : E26 + E27 + E28 + E29 + E30

Loc k Active

: E54 + E55

•

For washing machines with Frequency Inverter Controlled

motor only.

•

By this function it‘s possible to switch on the power for the

inverter if a technical intervention is needed.

•

By selecting YES, the power of the inverter is switched on.

S:Erase Fault

Messages? No

S:Output Power

Inverter : Off

S:View Fault

Statistics?

S:No Drain

0 x

Содержание FF10









































































































































Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды

Primus FF10, Руководство по программированию

Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды