Primus FF10 Скачать руководство пользователя страница 56

Страница: 56 / 136

PROGRAMMING MANUAL

100962 G PUBLICATION DATE 24 JUN 2008.DOC

↵

•

Liquid soap supplies can only be programmed if the selection

in the configuration menu is enabled.

•

The supplies can be programmed for an interval time

between 0 and 99 seconds.

•

The supply will not be activated if 0 Seconds is programmed.

•

Up to 4 supplies can function at the same time at the same

Sequence.

If you have programmed more then 4 supplies an error

message will be generated. Put the time of the supplies back

to zero until not more than 4 non-zero time values are

remaining.

•

The overview display shows the Supply Name and the

corresponding programmed time.

•

Insert the desired supply time. Press the ENTER button for

confirmation.

•

At the end of the Menu, when EXIT is displayed,

press the ENTER button to leave the supply Menu.

Attention !

For Front Soap Hopper washing machines, the soap is

added by programming the supplies A to E. (X22/5 A to D)

External liquid soap pumps correspond with the supplies

F to K.

For Top Soap Hopper washing machines, the External liquid

Soap pumps correspond with the supplies D to N.

The number of external supplies that is available depends
on the machine type.

•

The wash motor ON time can be programmed between 0 and

99 seconds.

•

The wash motor OFF time can be programmed between 3

and 99 seconds.

•

The suggested default values can be adapted in the

Initialisation menu.

•

Standard wash motor ON time of 12 seconds and a wash

motor OFF time of 3 seconds is recommended for normal

wash. A wash motor ON time of 3 seconds and a wash motor

OFF time of 12 seconds is recommended for a gentle wash

(woolens).

•

Insert the desired ON – OFF times. Press the ENTER button

for confirmation.

•

FS120, MB90, MB140, MB180 : 12Sec ON and 5Sec OFF

•

The Rinse Sequence can be programmed between 0 and

99 minutes in steps of 0.5 minutes.

•

The default time is 2.0 Minutes.

P:Pr XX Step XX

Time : 2.0 Min

P:Pr XX Step XX

Supply A: 0 Sec

P:Pr XX Step XX

On Time : _ _ Sec

P:Pr XX Step XX

Off Time : _ _ Sec

P:Soap Supply

Menu Exit

Содержание FF10









































































































































Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды

Primus FF10, Руководство по программированию

Результаты поиска

Содержание FF10

Отзывы:

Бренды по названию

Популярные бренды