background image

II

ACUTHERM ADVANTAGE - Manual 

  |   

acutherm.com

AdvAntAge - digitAl vAv diffusers

TABLE OF CONTENTS

Product Overview & Installation Instructions

General Description  .....................................................  1
Installation into Ceiling ................................................... 1
Power Supply to Master ................................................ 2
Drone Power Supply Connection................................... 3
Model Nomenclature ..................................................... 4
Model Configuration / Setpoint Adjustment  .................  6
Auxillary Heat ................................................................ 6
Optional Accessories ..................................................... 7
Advantage Power Module Optional Accessory .............. 7
TR115 / TR277 Transformer Optional Accessory ........... 8
Advantage Pressure Relief Collar Optional Accessory .... 8
Baffle Optional Accessory .............................................. 9
Supply Air Temperature Sensing .................................... 9
Thermostat Installation ................................................ 12

Display Navigation

Initial Setup ................................................................. 13
Information Menu 

(LCD Stats only)

 ...................................... 14

Service Menu 

(LCD Stats only)

 ............................................ 15

 

Balancing Menu ................................................... 16

 

VVT Menu

 (Pressure Dependant Mode)

 ............................. 17

 

Setpoint Menu 

(Setpoint Limits and Temperature Units)

 .......... 18

 

Input Menu 

(Supply Air Temp and Neutral Mode)

 .................. 19

 

Output Aux Binary Menu ...................................... 20

 

Output Analog Menu ............................................ 21

 

BACnet Menu

 (BACnet Addressing Setup)

 ........................ 22

 

Stat Setup Menu .................................................. 23

Display Options Menu ................................................. 24

Native BACnet Network Interface Optional Accessory

BACnet Module  .........................................................  25
BACnet Wiring  ..........................................................  26
Network Wire Specifications  ......................................  27 
BACnet Service Menu  ...............................................  28
BACnet Module  .........................................................  27 
BACnet Networking and Setup  .................................  30
Setting the Device Instance (

Coupled MAC and DI)

  .............  31 

Maintenance

Troubleshooting Guide ................................................ 31
Master Specifications .................................................. 33
Drone Specifications ................................................... 33

Having difficulty installing this product?  
Acutherm is here to help.

Application support

510.785.0510

[email protected]

acutherm.com

suPPOrt   

Содержание acutherm Advantage





































Отзывы: