background image

AdvAntAge - digitAl vAv diffusers

PRODUCT OVERVIEW & INSTALLATION INSTRUCTIONS

4

ACUTHERM ADVANTAGE - Manual 

  |   

acutherm.com

Thermostat Options

The Advantage Master uses a wall 
thermostat to accurately sense room 
temperature in both cooling and heating 
modes.  Each thermostat comes 
complete with a 35ft plenum rated cable 
for connection to the Advantage Master. 

The thermostat is available in six 
options:
•  Room Sensor (Blank Face).
•  Dial Thermostat
•  LCD Thermostat
•  LCD Thermostat with motion sensor 

for occupancy

•  LCD Thermostat with CO2 and 

humidity sensors

•  Wireless Thermostat

The LCD thermostats are used to adjust 
set points, display room temperature, 
and configure the different parameters of 
the diffuser.

nOte   

 When using the Room Sensor 

or Dial Thermostat order a LCD-
SET (minimum of one per project) to 
configure the diffuser.

Thermostat Adjustment

VAV Cooling, VAV Heating - Connecting 

a wall mounted T’stat activates the 

Advantage. Connect the T’stat to 

Advantage using a supplied NETC35 

(35’ plenum rated cable) by snapping 

one side of the plug into jack inside of 

thermostat, and the other side into the 

T’Stat In jack. Setpoint is adjusted using 

the wall mounted sensor.
See page 10 and 11 for more 

thermostat details.

ROOM SENSOR

DIAL THERMOSTAT LCD THERMOSTAT

LCD THERMOSTAT WITH 

CO2 AND HUMIDITY

LCD THERMOSTAT 

WITH MOTION

SENSOR

WIRELESS 

THERMOSTAT

figure 8 - drOne Wiring diAgrAM   

RED LED

DC SIGNAL STATUS TO DRONE

GREEN LED

24 VAC SIGNAL STATUS

1 & 6 = 2 -10VDC

2 & 5 = COMMON

3 & 4 = 24VAC

FROM PREVIOUS

DIFFUSER

CABLE

CABLE

TO NEXT

DIFFUSER

INTERNAL WIRING

Содержание Acutherm Advantage Master







































Отзывы: