PRG BEST BOY Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 100

PRG BEST BOY Скачать руководство пользователя страница 70

62

BEST BOY

®

HP SPOT LUMINAIRE USER MANUAL

SOFTWARE UPDATE

Software Update Using LumLoader Application

Introduction

The LumLoader application allows you to update the software in a Best Boy HP Luminaire. The update will be sent
over an Ethernet connection. The luminaire can take the Ethernet input directly, or the update can be translated to
DMX512 signal with an appropriate device, either Series 400® or a PRG Node (with the required software update).
The fixtures can be daisy-chained to load multiple fixtures at once.

Supported configurations:

Note:

There should be no active control (DMX512 or Ethernet) during the update process.

Preparation - Java

The loader (LumLoader) is a Java application which can be run on a Mac or a PC computer.

Note:

Microsoft Windows® and new Mac computers do not come with the required Java run-time library installed, so

you may need to go to the Sun website (java.com/getjava/) to download Java.

Selecting an Ethernet Interface

Connect the computer to the system, and start the LumLoader application. When the application starts, it will ask
which active Ethernet port should be used. Select the appropriate port. You may be able to differentiate the ports by
IP address, compared with your network setup. Typically the en0 is the first built-in Ethernet port, and other interfaces
could include additional network ports or wireless adapters.

Selecting the Module

The loader can support multiple versions of software, so make sure the appropriate version is selected. The default
version will typically be fine.

Download the Software

Press "Start Download" to initiate the update. You should see the luminaires immediately drop into the startup screen
and erase flash, which takes about 30 seconds. Then the new module is sent out, the screen indicates "Loading",
and when complete they will go back to the main menu and start calibration.

If the fixture already has the update software version, it will not attempt the update.

Mac/PC Ethernet Best Boy Ethernet Best Boy ...

Mac/PC Ethernet Series 400 Ethernet Best Boy Ethernet Best Boy ...

Mac/PC Ethernet Series 400 DMX Best Boy DMX Best Boy ...

Mac/PC Ethernet PRG Node DMX Best Boy DMX Best Boy ...

«
...
68
69
70
71
72
...
»

Содержание BEST BOY





































































































Отзывы:

Нет отзывов