PRG BAD Boy страница 34 Скачать руководство пользователя

Страница: 34 / 76

™ S

POT

UMINAIRE

SER

ANUAL

2 4

02.9812.0001A

Menu Details

Home Screen

The Home screen consists of several sections (referred to here as "panels") which provide status and
configuration information. Pressing the panels on the touchscreen will open the applicable sub-menus.

LAMP Panel

•

Lamp Status

- displays lamp on/off status, hours, temperature and

power level. The lamp icon color indicates status of lamp: off = gray
icon, on = yellow icon (shown in example at right), error = red icon.

•

Power Level

- displays current APS command: 700-1400 watt.

•

Lamp Hours

- displays total lamp hours. Lamp hours are shown in

green if under threshold, yellow if close to threshold, or red if over
threshold.

•

Temperature

- displays luminaire head temperature. The temperature

is shown in green if under limit, yellow if close to the limit, and red if
over the limit.

Press panel to open

Lamp Screen

CONFIG Panel

•

Address

- displays current DMX512 address 001-470.

•

Universe

- displays current Art-Net universe (alpha A-JE or numeric 0-255), if Art-Net is present.

Press panel to open

Configuration Screen

INFO Panel

•

Run Time

- displays current run time in

hours:minutes

format.

Press panel to open

Information Screen

TEST Panel

Press panel to open

Test Screen

COMM Panel

•

Comm

- displays currently active input protocol: ETH, DMX (green) or NONE (red).

Press panel to open

Communication Screen

STATUS Panel

•

Status

- displays fixture status: CAL (yellow), OK (green), or ERR (red).

Press panel to open

Status Screen

Home Screen

Содержание BAD Boy













































































Результаты поиска

Содержание BAD Boy

Отзывы:

Похожие инструкции для BAD Boy

Бренды по названию

Популярные бренды

PRG BAD Boy, Руководство пользователя

Результаты поиска

Содержание BAD Boy

Отзывы:

Похожие инструкции для BAD Boy

Бренды по названию

Популярные бренды