PRG BAD Boy Скачать руководство пользователя

Страница: 50 / 76

™ S

POT

UMINAIRE

SER

ANUAL

4 0

02.9812.0001A

Mechanism Errors

Errors will be shown after the mechanism code, for example: PAN:Comm Error.

Other Errors

Error Code

Explanation

Comm Error

Error communicating with motion processor

Init Error

Error during initialization of motion processor

Cal Error

Error resetting position values in motion processor at beginning of calibration

Cal Timeout

An action during calibration took longer than expected

No Stop

Mechanism which calibrates to a physical stop did not find that stop

Sensor Stuck

During calibration, could not find either edge of the sensor or the sensor did not turn off
as expected

No Sensor

During calibration, no sensor was found in the range of travel

Hall Sensor Edge

Found sensor, but couldn't find far edge

Motion Error

Mechanism's actual position is too far from its commanded position

Command Error

Error while sending commands to the motion processor

Get Position Error

Error when retrieving current position from motion processor

Spin Error

Error while sending spin command to motion processor

Stop Spin Error

Error while sending stop spin command to motion processor

Spin Stop Timeout

Spinning mechanism did not come to rest in the given period

Error Code

Explanation

Temp over threshold

Temperature too high

Lamp over threshold

Lamp hours above recommended maximum

Lamp Off

Fan Error: Cannot strike lamp while any fan is in error state

Pan/Tilt Aux Encoder Error

Auxiliary encoder value is too far from the main encoder value

Gobo out of zero range

When zeroing gobo wheels, the wheel is too far away from zero to set the
position

DMX busy: cancel crossload

Cannot execute crossload with traffic on DMX line

Data not crossload format

Data in memory is not proper format for crossload

DMX: UART transmit error

Transmit buffer busy when trying to send

Crossload Timeout

Crossload execution took too long due to error

CAN Comm Error

Stopped receiving CAN messages from motion processor

Main Fan Error

Main fan CAN messages not received or fan not running properly

UPE Fans Error

Upper Enclosure fans not running properly

Pinch Fan Error

Pinch fan not running properly

Stack Fan Error

One or more stack fans not running properly

Содержание BAD Boy













































































Результаты поиска

Содержание BAD Boy

Отзывы:

Похожие инструкции для BAD Boy

Бренды по названию

Популярные бренды

PRG BAD Boy, Руководство пользователя

Результаты поиска

Содержание BAD Boy

Отзывы:

Похожие инструкции для BAD Boy

Бренды по названию

Популярные бренды