Precor PVS Скачать руководство пользователя страница 11

Rewire the Upright Bike

NOTE

You need to remove only one side cover to thread the cables.

To thread the new cables through the equipment:

Step

Procedure
Use a #2 Phillips screwdriver to remove the two self-tapping screws

holding the rear cover in place. Pull the upright rear cover back to

remove it.
Remove the two self-tapping screws holding the top cover in place.

Slide up the rubber seal and then lift off the cover.
Remove the four self-tapping screws holding the left side cover in

place, then pull the cover away from the body assembly. Guide the

cover around the pedal crank, then remove it.
Remove blank jack panel at base of bike and feed the cables down

the mast.
The cables need to be threaded around the bolts that hold the center

mast in place.
Guide the ends of each cable through the gap at the bottom of the

center column. Remove the CAT5 (Ethernet) coupler from the square

hole in the jack panel, then feed the cables through the hole.

Important The cables must be secured in the cable retainers along the

frame and then exit the square hole in the jack panel. You may need to

slide out the jack panel to remove the CAT5 coupler and feed the cables

through the hole. If so, return the jack panel to its previous position when

you are finished.

N/A

Reattach the bike covers.

2

1

1

Содержание PVS





















Отзывы: