Precor C844 Скачать руководство пользователя страница 9

Страница: 9 / 54

C844 Upright Cycle

Page 9

Procedure 2.3 - Selecting Club Settings

This procedure allows the modification of the following settings:

•

U. S. Standard/Metric

•

Line Voltage Selection

•

Get Max Workout Time

Plug the power cord into the wall outlet, then turn on the cycle with the ON/OFF switch.

With the

PRECOR C844

banner scrolling, press the

QUICKSTART

and

WORK LEVEL

▲

keys simultaneously. Across the left display window scrolls either the banner

U. S.

Standard

or the banner

Metric

If you wish to change the measurement standard . . .

THEN . . .

OTHERWISE . . .

Use the

DOWN

keys to toggle

Continue with the next step.

to an alternate measurement standard;
then continue with the next step.

Press

ENTER

, then release. The line voltage currently selected is displayed on the left

display window.

If you wish to toggle to the alternate line voltage. . .

THEN . . .

OTHERWISE . . .

Use the

DOWN

keys to toggle

Continue with the next step.

to the alternate line voltage; then
continue with the next step.

Press

ENTER

, then release. The maximum workout time is displayed on the left display

window.

If you wish to change the maximum workout time . . .

Содержание C844























































Результаты поиска

Содержание C844

Отзывы:

Precor C844, Руководство пользователя, Страница: 9 / 54

Результаты поиска

Содержание C844

Отзывы: