Precor C844 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 54

Precor C844 Скачать руководство пользователя страница 2

C844 Upright Cycle

Page 2

Section One - Things You Should Know

Right, Left, Front, and Back Conventions

In this manual, right, left, front, and back are from the perspective of a user sitting on the C844,
facing the display enclosure.

Warning and Caution Statements and General Safety Guidelines

Warning statements indicate a particularly dangerous activity. Warning statements you will find in
this manual include:

•

To remove power from the C844, the power cord must be disconnected from the wall outlet.
Always ensure that the C844 is unplugged from the wall outlet when you inspect or adjust the
C844, or when you isolate, remove, or replace a C844 component.

•

Removing the covers exposes high voltage components and potentially dangerous
machinery. Exercise extreme caution when you perform maintenance procedures with the
hood removed.

•

During service operations you will be very close to moving machinery and high voltage
components. When you perform maintenance procedures with the covers removed, remove
jewelry (especially from ears and neck), tie up long hair, remove neck ties, and do not wear
loose clothing.

•

Exercise caution when touching any wire or electrical component during C844 operation.

•

The flywheel is very heavy. Be prepared for the weight of the flywheel when it comes off of
the flywheel shaft.

Caution statements are intended to prevent damage to the C844 as a result of the current
activity. Caution statements included in this manual are listed below:

•

Notice the orientation notch on the PROM (U3). These components must be positioned with
the same notch orientation.

•

When it is necessary to lift the C844, ensure that the C844 has adequate support. Do not lift
the C844 by the front cross-member.

Safety

guidelines you should know and follow include:

•

Read the owner’s manual and follow all operating instructions.

•

Visually check the C844 before beginning service or maintenance operations. If it is not
completely assembled or is damaged in any way, exercise extreme caution while operating

«
1
2
3
4
...
»

Содержание C844























































Отзывы:

Нет отзывов