Precor C844 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 54

Precor C844 Скачать руководство пользователя страница 38

C844 Upright Cycle

Page 38

Procedure 7.5 - Replacing the AC Input Module

WARNING

Always turn off the C844 with the ON/OFF switch and unplug the power cord from the wall outlet
before you service the cycle.

1.

Place the C844 Cycle on its front end. Remove the pan from the base of the cycle.

2.

Remove the power cord from the AC input module.

3.

Disconnect the brown and blue wires from the AC input module.

4.

Remove the screw that secures the green ground wire to the cycle frame.

5.

Depress the mounting tabs and push the AC input module out of the base plate.

6.

Position the new AC input module at its mounting position.

7.

Position the green ground wire at its mounting location. Replace the screw that secures the
green ground wire to the cycle frame.

8.

Connect the brown and blue wires disconnected in Step 3 to the AC input module.

9.

Plug the power cord into the AC input module.

10. Install the pan to the base of the cycle. Return the cycle to its upright position.

11. Check the cycle operation as described in Section Four.

«
...
36
37
38
39
40
...
»

Содержание C844























































Отзывы:

Нет отзывов