Precor C844 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 54

Precor C844 Скачать руководство пользователя страница 11

C844 Upright Cycle

Page 11

Procedure 2.4 - Documenting Software Problems

When a problem is found with either the software or upper or lower PCA’s, record the information
listed below. If you isolated the problem to either the PROM, upper PCA, or lower PCA, include
the information you recorded with the malfunctioning PROM or PCA when you ship it to Precor
Customer Support.

When a problem occurs, record the following information:

•

Model and serial number

Note:

The model serial number is located on the bottom of the lower crossbeam.

•

Software version number

•

Odometer reading

Note:

Determine the version number of the PROM mounted on the upper PCA as described in
Procedure 2.1.

•

User and program number running when the problem occurred

•

A description of:

a. What happened or failed to happen

b. The action taken by the user just before the problem occurred

c. Problem related information (such as how far into the program the problem occurred, the

work level being used when the problem occurred, etc.)

•

The frequency of occurrence

«
...
9
10
11
12
13
...
»

Содержание C844























































Отзывы:

Нет отзывов