PRECITEC CHRocodile C Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 63

PRECITEC CHRocodile C Скачать руководство пользователя страница 39

40

SRA

<3..17, ?>

<index of sample rate>
<sample rate in Hz>HZ

set Sample Rate

Compatibility command 3:32Hz, 4:100Hz, 5:320Hz,
6:1000Hz, 7:2000Hz, 8: 3200Hz, 9: 4000Hz(default)
See also: SHZ

SRI

<1..5>

<refractive index> at
spectral d-line (587,567
nm)

Set/query Refractive Index

Only active, if SRT 0 selected (no preloaded Index table)

1.0(default)-5.0
You should give as many indices as there are layers to
be measured, that is (number of Peaks - 1). The _rst
parameter describes the nearest Layer.

See also: ABE, SRT

SRT

<0..16>

<0..16>:name of
table [CR/LF]

Set Refractive index Table

Preloaded Tables can be used instead of SRI/ABE.
SRI/ABE is active when table 0 is choosen (SRT 0)
You should give as many table indices as there are layers
to be measured, that is (number of Peaks - 1). The _rst

parameter describes the nearest Layer.
See also: SRI, ABE

SSQ

two binary bytes -

Synchronisation SeQuence

2 Byte sync sequence used only in $-protocol

SSU

-

-

Save SetUp

Saves the current setting to nonvolatile memory. The

Sensor will restart on the next power-up with this
configuration.

STA

-

-

STArt data flow

(default) Sending of measurement data enabled.

See also: STO

STO

-

-

STOp data flow

Sending of measurement data disabled. Only Command
responsesor updates are transmitted.

See also: STA

THR

<0..4094, ?>

<threshold value>

detection THReshold

threshold for peak detection in the confocal modes (0 and
1)

0-4095, default is 50

TRE

-

-

TRigger Each Mode

Every exposure (or exposure burst in case of averaging)
needs a trigger event (e.g. rising edge on Trigger input).
All exposures will begin exactly at the trigger events as
long as the previous exposure is ended. If the previous
exposure is still ongoing, the trigger will be delayed. If
the device receives a trigger event, while the precedent
trigger still waits for execution, the trigger event will be
lost and the trigger lost counter will be incremented.

See also: TRG, TRW, CTN

TRG

-

-

TRiGger

once

Stops the free running measurement and waits for a
trigger event. The trigger event restarts free running

«
...
37
38
39
40
41
...
»

Содержание CHRocodile C
































































Отзывы:

Нет отзывов