PRECITEC CHRocodile C Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 63

PRECITEC CHRocodile C Скачать руководство пользователя страница 27

28

Operational Start up

3.1

Connections and Interfaces

All of the connection ports are located at the rear of the CHRocodile C (Cf. section 2.6 Connections
and Interfaces):



The power supply jack,



The RJ45 standard connector for Ethernet communication,



The multipoint connector interface (9 pins) for trigger input / output and RS422/RS232 serial

communication,

3.1.1

CHRocodile C Stand Alone device:

The device can be used as a stand-alone device in order to perform selective  distance or thickness
measurements.  In  this  condition,  only  the  power  supply  and  Ethernet  connector  or  multipoint
connector are useful.

Power supply

The CHRocodile C has two pluggable screw terminal for power supply with 24V

DC

+/-10%.

Connect the set of power cable supply associated to the Power Supply Adapter (100-240VAC to
24V

DC

+/-10%) delivered with the CHRocodile C unit.

Ethernet connector

Connect the isolated RJ45 standard connector from the CHRocodile C unit to an Ethernet network
(PC). Use shielded cable for the data port connection (minimum category 5 cable).

The default CHRocodile C IP address is:

192.168.170.4

Configure the PC Ethernet port to the following address:

192.168.170.X (X≠4)

The CHRocodile C can also be configured to use auto-configuration of the IP-Address through
a DHCP server.

To configure the Ethernet port of your PC,

you must open the ‘

Network connection properties’

menu.

After selecting the right Ethernet card (connected to the sensor), click on ‘

network protocol (TCP/IPv4)’

and click ‘

Properties’.

Set the IP address of the PC and the mask. For a standard use the mask should

be set to 255.255.255.0.

If you need to configure the sensor to another IP address (different than 192.168.170.4), you need to
use  the  $IPCN  command  (Cf.  Appendix  1).  This  could  be  useful  in  case  of  multiple  CHRocodile  C
connection on a single computer.

«
...
25
26
27
28
29
...
»

Содержание CHRocodile C
































































Отзывы:

Нет отзывов