PowerStroke PS80903A, Руководство оператора

Страница: 10 / 48

Page 10 — English
OPERATION
ADDING/CHECKING ENGINE LUBRICANT
See Figure 10, page iv.
NOTE:
This machine has been shipped with approximately
2 oz. of lubricant in the engine from testing.
you must add
lubricant to the engine before starting it the first time.
CAUTION:
Any attempt to start the engine without adding lubricant
will result in engine failure.
To add engine lubricant:
 Place pressure washer on a flat, level surface.

Unscrew the oil cap / dipstick by turning counter-
clockwise.
 Using 4-stroke engine lubricant (SAE 30 or SAE 10W30),
fill to the upper level of the oil filter neck (18 oz., 4-cycle
engine lubricant provided).

Replace the oil cap / dipstick and securely tighten.
NOTE:
This engine has a total lubricant capacity of
19.5 oz. (0.61 qt.) .
To check engine lubricant level:

Set engine on a flat surface.

Wipe dipstick clean and re-seat in hole; do not
rethread.

Remove dipstick again and check lubricant level. Lubricant
level should fall within the hatched area on the dipstick.

If level is low, add engine lubricant until the fluid level
rises to the upper portion of the hatched area on the
dipstick.

Replace and secure the oil cap/dipstick.
CAUTION:
Do not overfill. Overfilling the crankcase may cause ex-
cessive smoke and engine damage.
OXyGENATED FUELS
Some conventional gasolines are blended with alcohol or an
ether compound. These gasolines are collectively referred
to as oxygenated fuels. To meet clean air standards, some
areas of the United States and Canada use oxygenated fuels
to help reduce emissions.
If using an oxygenated fuel, make sure it is unleaded and
meets the minimum octane rating requirements. Before using
an oxygenated fuel, try to confirm the fuel’s contents. Some
states/provinces require this information to be posted on the
pump. The following are the EPA approved percentages of
oxygenates:
Ethanol (ethyl or grain alcohol) 10% by volume. You
may use gasoline containing up to 10% ethanol by volume.
Gasoline containing ethanol may be marketed under the
name “Gasohol.”
Do not use E85 fuel.
MTBE (methyl tertiary butyl ether) 15% by volume.
You
may use gasoline containing up to 15% MTBE by volume.
Methanol (methyl or wood alcohol) 5% by volume. You
may use gasoline containing up to 5% methanol by volume
as long as it also contains cosolvents and corrosion inhibi-
tors to protect the fuel system. Gasoline containing more
than 5% methanol by volume may cause starting and/or
performance problems. It may also damage metal, rubber,
and plastic parts of the product or your fuel system.
If you notice any undesirable operating symptoms, try another
service station or switch to another brand of gasoline.
NOTE: Fuel system damage or performance problems re-
sulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated previously are
not covered under warranty.
ADDING GASOLINE TO THE FUEL TANK
See Figure 11, page iv.
WARNING:
Gasoline and its vapors are highly flammable and
explosive. To prevent serious personal injury and prop-
erty damage, handle gasoline with care. Keep away from
ignition sources, handle outdoors only, do not smoke
while adding fuel, and wipe up spills immediately.
When adding gas to the pressure washer, make sure the unit
is sitting on a flat, level surface. If the engine is hot, let the
pressure washer cool before adding gas. ALWAYS fill the
fuel tank outdoors with the machine turned off.
NOTE:
Use unleaded gas only. DO NOT mix lubricant with
gas.

Before removing the fuel cap, clean the area around it.
Remove the fuel cap.

Insert a clean funnel into the fuel tank then slowly
pour gasoline into the tank. Fill tank to approximately
1-1/2 in. below the top of the tank neck (this allows for
fuel expansion).

Replace fuel cap and tighten until the cap “clicks”.

Clean up any spills before starting the engine.