Powerbuilt EGS0252 Скачать руководство пользователя страница 32

Страница: 32 / 40

TROUBLESHOOTING GUIDE

Problem

Probable Cause

Solution

Engine shuts down when

running.

1. Out of petrol.

2. Low Engine Oil

1. Fill petrol tank.

2. Add oil.

Engine will not start; or

starts and runs rough.

1. Engine On/Off set to

“OFF” position.

2. Petrol valve is in

“OFF” position.

3. Dirty air cleaner.

4. Out of petrol.

5. Stale petrol.

6. Spark plug wire not

connected to spark plug.

7. Bad spark plug.

8. Water in petrol.

9. Flooded.

10.Excessively rich

petrol/air mixture.

11.Intake valve stuck

open or closed.

12.Engine has lost

compression.

13.Low engine oil.

14.Wrong Petrol.

15.Engine is too hot

16.Choke is in wrong

position

17.Pressure builds up

after 2 pulls on starter

coil or after initial use.

1. Set switch to “ON”

position.

2. Turn petrol valve to

“ON” position.

3. Clean or replace air

cleaner.

4. Fill petrol tank.

5. Drain petrol tank and

carburetor; fill with

fresh petrol.

6. Connect wire to spark

plug.

7. Replace spark plug.

8. Drain petrol tank and

carburetor; fill with

fresh petrol.

9. Wait 5 minutes and

re-crank engine.

10.Coutact authorised

service facility.

11.Coutact authorised

service facility.

12.Coutact authorised

service facility.

13.Add oil.

14.Use recommended

petrol.

15.Allow engine to cool

16.Change choke

position

17.Squeeze gun trigger

to relieve pressure.

Содержание EGS0252








































Результаты поиска

Содержание EGS0252

Отзывы:

Похожие инструкции для EGS0252

Бренды по названию

Популярные бренды

Powerbuilt EGS0252, Инструкция по эксплуатации

Результаты поиска

Содержание EGS0252

Отзывы:

Похожие инструкции для EGS0252

Бренды по названию

Популярные бренды