Powerbuilt EGS0252 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

background image

8. Pull the handle lock

pin and fully raise the

handle upright.

Release and snap the

lock pin into its lock-

ing hole in the frame.

9. Assemble the top and

bottom gun holders

(using the nuts and

bolts) to the frame as

shown. Tighten all

mounting hardware.

PRESSURE HOSE TO PRESSURE PUMP

Connect the hose to the pressure pump outlet and FIRMLY

tighten the nut by hand.

fitting and release collar. Tug on the

hose to make sure it is secured.

PRESSURE HOSE TO SPRAY GUN

Connect the hose to the spray gun and FIRMLY tighten

the nut by hand.

2.

Insert male quick-disconnect fitting on spray

gun into female quick-disconnect on high pressure hose

3. Release slip ring on female quick-disconnect and

twist. Listen for “click” to ensure both quick-disconnects are coupled.

4. Pull high pressure hose and spray gun in opposite direction to ensure they do

not separate.

SPRAY WAND TO SPRAY GUN

1. Remove the protective plastic cap at the inlet of the wand.

2. Thread spray wand onto spray gun.

3. Tighten the nut to secure the Wand to the Gun.

16

2400 PSI / 12 LPM

NUT

GUN HOLDER (TOP)

GUN HOLDER
(BOTTOM)

LEG (2)

SHAFT

LOCK NUT

COTTER PIN

LOCK NUT

LOCK NUT

BOLT

BOLT

BOLT

WHEEL (2)

BUSHING

WASHER

HANDLE
LOCK PIN

«
...
16
17
18
19
20
...
»

Содержание EGS0252









































Отзывы:

Нет отзывов

Похожие инструкции для EGS0252

Бренд: Campbell Hausfeld Страницы: 8

Бренд: Rac Страницы: 5

Бренд: Midea Страницы: 32

Бренд: Samsung Страницы: 112

SUNJOE SPX7000E-RM

Бренд: SNOWJOE Страницы: 20

Бренд: Kärcher Страницы: 220

Бренд: Generac Power Systems Страницы: 24

Бренд: Kärcher Страницы: 112

Бренд: Hotpoint Страницы: 72

Бренд: Comet Страницы: 132

Бренд: Kruger Страницы: 72

Бренд: Bush Страницы: 48

Бренд: Speakman Страницы: 2

Бренд: Samsung Страницы: 80

Бренд: Candy Страницы: 41

TOUCHTRONIC W 3039

Бренд: Miele Страницы: 60

Бренд: Miele Страницы: 48

Бренд: Miele Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды