Powerbuilt EGS0252 Скачать руководство пользователя страница 30

Страница: 30 / 40

TO PROTECT AGAINST RUST FORMATION DURING STORAGE, OIL

THE CYLINDER BORE:

• Remove spark plug and pour approximately 15 ml of clean engine oil into the

cylinder.

• Install spark plug.

• Make sure engine

ON/OFF

switch is

OFF

. Slowly pull the starter cord 2 to 3 times to

distribute and coat the cylinder bore with oil.

DO NOT

start engine at this time.

Unintentional sparking can cause fire or electrical shock.

Failure to observe this warning can cause severe property

damage, severe burns and even death.

Disconnect spark plug wire from spark plug and cover tip of spark plug wire

with insulating tape and place wire where it cannot come in contact with

spark plug or Waterblaster frame.

PRESSURE PUMP

1. Drain all water from pressure hose, coil and store it in cradle of pressure

washer handle.

2. Drain all water from spray gun and spray wand by holding spray gun in vertical

position with nozzle pointed downward. Squeeze trigger to remove fluids from

spray gun and spray wand. Store in spray gun/hose holder.

3. Store chemical hose, high pressure hose and spray wand so they are protected

from damage, such as being run over.

It is

RECOMMENDED

that you follow these steps to protect the internal seals of

Waterblaster when storing unit for more than 30 days and/or when freezing temper-

atures are expected.

1. Obtain a funnel, six ounces of RV antifreeze and approximately 0.9 m of garden

hose with a male hose connector on one end.

Use only RV antifreeze.

Any other type of antifreeze is

corrosive and can damage pressure pump.

2. Connect 0.9 meters length of garden hose to water inlet of pressure pump.

3. Add RV antifreeze using the funnel.

Содержание EGS0252








































Результаты поиска

Содержание EGS0252

Отзывы:

Похожие инструкции для EGS0252

Бренды по названию

Популярные бренды

Powerbuilt EGS0252, Инструкция по эксплуатации

Результаты поиска

Содержание EGS0252

Отзывы:

Похожие инструкции для EGS0252

Бренды по названию

Популярные бренды