background image

21 

13.2.  Before storing the welder generator for an extended period of time please ensure that the 

area of storage is free from excessive dust and humidity. Please follow the table below: 

STORAGE TIME RECOMMENDED MAINTENANCE   

0 – 1 MONTH 

 

NO PREPARATION REQUIRED 

1 – 2 MONTHS 

 

DRAIN OUT ORIGINAL FUEL IN THE FUEL TANK AND REPLACE WITH CLEAN FUEL 

2 – 12 MONTHS 

 

DRAIN OUT ORIGINAL FUEL IN THE FUEL TANK AND REPLACE WITH CLEAN FUEL 

 

EMPTY ALL FUEL FROM THE CARBURETOR 

 

EMPTY FUEL FROM THE FUEL SEDIMENT CUP 

>12 MONTHS 

 

DRAIN OUT ORIGINAL FUEL IN THE FUEL TANK AND REPLACE WITH CLEAN FUEL 

 

EMPTY ALL FUEL FROM THE CARBURETOR 

 

EMPTY FUEL FROM THE FUEL SEDIMENT CUP 

 

REMOVE THE SPARK PLUG AND POR A TEASPOON OF 4 STROKE ENGINE OIL INTO 

THE CYLINER. TURN THE ENGINE SLOWLY BY PULLING ON THE RECOIL STARTER. 

REINSTALL THE SPARK PLUG 

 

DRAIN THE OLD OIL AND REPLACE WITH CLEAN OIL 

 

AFTER REMOVAL FROM STORAGE, DRAIN THE STORED FUEL INTO A SUITABLE 

CONTINER AND REPLACE WITH FRSH FUEL BEFORE STARTING 

 

DRAIN THE CARBURETOR BY LOOSENING THE DRAIN SCREW. DRAAIN THE FUEL INTO A SUITABLE 

CONTAINER. REINSTALL THE DRAIN PLUG. 

 

HAVING SWITCHED THE FUEL COCK OFF, REMOVE THE SEDIMENT CUP, EMPTY THE FUEL, THEN 

REINSTALL THE CUP AND SECURE IT PROPERLY. 

Содержание SRFW-250E




























Отзывы: