manualshive.com logo in svg

Potec PRK-8000, Руководство по эксплуатации

Поделиться
Скачать
Potec PRK-8000 Скачать руководство пользователя страница 45

PRK-8000 Operation Manual

 

- 37 - 

 

[ page2 ] 

[Measuring Modes, etc.] 
MODE   Assigns order of Measurement Modes “REF, KER, K/R, CLBC, K(P)” and 

delete unnecessary modes.

 

1: 

First mode that is displayed when power is turned ON. It cannot be 
set to “OFF”. 

2~5:     Second modes and after. 

z

  Assign First Measurement Mode and after. 

z

  If you want to delete unnecessary modes, delete from last(5

th

) one. 

SKIN:     Set the background color of menu button.   
 

     Color 

changes 

will 

apply from then exit the SETUP mode. 

 

     BLACK: 

Set menu background color to black. 

           WHITE: 

Set menu background color to white. 

BEEP   
 

     ON:   Enable 

BEEP sound in measurement mode. 

 

     OFF: 

   Disable BEEP sound. 

POWER SAVE TIME (min) 

OFF:     Disable Power Save Function. 
5: 

    Enter 

Power 

Save 

Mode 

if 

there 

is on operation by operator about 5 minutes. 

10:    Enter 

Power 

Save 

Mode if there is on operation by operator about 10 minutes. 

30:    Enter 

Power 

Save 

Mode if there is on operation by operator about 30 minutes. 

SYS-V    

If you press the “LOAD DEFAULT SYSVAR” button, the system variable will 
be initialized. 

      Ver. 

It displays the version of the Software that is currently applied to the product. 

          MOTER Ver. 

It displays the version of the MOTOR control Software that is currently applied 
to the product. 

 

Содержание PRK-8000





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды