manualshive.com logo in svg

Potec PRK-8000, Руководство по эксплуатации

Поделиться
Скачать
Potec PRK-8000 Скачать руководство пользователя страница 23

PRK-8000 Operation Manual

 

- 15 - 

5.2 Refractometry [REF Mode]

   

 

Only refractometry can be performed in the REF mode. 
 
(1)    Enter REF Mode 

Press 

MODE button

 on the left side of the display, and then select “

REF

”. 

 
(2)  Follow the same procedure (2) of the Continuous Keratometry and Refractometry [K/R 

Mode]. 

 
(3)    Perform alignment and Focusing 

Align the pupil and alignment marks, and focus on the mire image by using the 
operation lever. The focus is correct, the color of the aiming mark changes to yellow 
color. 

 
(4)   Measurement 

Press the measuring button . 
Measurement will be continuously performed when the measuring button    is kept 
pressed. 

z

  If you change setting for REF/KER of SETUP Mode, you can select the vertex 

distance. 

z

  If you change setting for REF/KER of SETUP Mode, you can change display format 

of CYL value. 

 

 

 

NOTES: 

①

   There can be error if the Outer Alignment Mark and the pupil is eccentric. 

②

  There may be some aberration to the measurement value due to the 

eccentricity or inclination of lens, or deformation of cornea after surgery. 

Содержание PRK-8000





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды