Potec PRK-8000 Скачать руководство пользователя страница 17

Страница: 17 / 52

PRK-8000 Operation Manual

- 9 -

Power ON

DISPLAY Mode

DISP

button

EXIT

button

SETUP Mode

SETUP

button

EXIT

button

SIZE Mode

SIZE

button

EXIT

button

ILLUM Mode

ILLUM

button

EXIT

button

REF Mode

MODE

button

KER Mode

MODE

button

K/R Mode

MODE

button

CLBC Mode

MODE

button

K(P) Mode

MODE

button

IOL Mode

IOL

button

EXIT

button

5. Measurement

WARNING

Should any of the following occur, immediately turn OFF the power
switch, unplug the power cable from the AC outlet, and contact the
dealer or the agent who/where you purchase this instrument.

When there is smoke, strange odor or abnormal sound.

When liquid has been spilled into the instrument or a metal object

has entered through an opening.

When the product has been dropped or its housing damaged.

Relation between buttons and modes

NOTE: IOL button will be enabled at K/R mode and REF mode only. If IOL

button is pressed, IOL measurement will be performed and pressed
again to render the basic measurement.

Содержание PRK-8000





















































Результаты поиска

Содержание PRK-8000

Отзывы:

Бренды по названию

Популярные бренды

Potec PRK-8000, Руководство по эксплуатации

Результаты поиска

Содержание PRK-8000

Отзывы:

Бренды по названию

Популярные бренды