manualshive.com logo in svg

Potec PRK-8000, Руководство по эксплуатации

Поделиться
Скачать
Potec PRK-8000 Скачать руководство пользователя страница 19

PRK-8000 Operation Manual

 

- 11 - 

(3) 

Perform alignment and Focusing 

 

CAUTION

 

Do not place your hand or fingers between the stage and base. Also 
ensure that the examinee does not place his/her hand or fingers there 
either. Otherwise, hand or fingers may be hurt. 

 

Slide the operation lever to the left so that the right eye of the examinee is displayed on 
the monitor. 
Ask the examinee to look at the red roof in the center of the scene (eye fixation target). 
Looking at the monitor, check that image of the mire ring is not obscured by the upper 
eyelid. If it is covering the ring, instruct the examinee to keep his/her eye opened wide 
until measurement ends. Or help them open the eye wider by lifting up his/her upper 
eyelid lightly with your fingers. 
Looking at the monitor, incline the operation lever to right or left, and turn the operation 
lever so the pupil is concentric with the inner alignment mark. If the pupil is large, align it 
with the outer alignment mark. 
Focus on the mire image by inclining the operation lever forward and backward. The 
focus is correct, the color of the aiming mark changes to yellow color.

 

 

 

 

 NOTES: 

①

 Slide stage to the forward/backward and right/left if you are unsatisfied with 

the operation lever control. 

②

  If the alignment marks and the pupil are not concentric, instruct the examinee 

to look at the red roof at the center of the picture. Otherwise, measurement 
error may occur due to aberration.   

 
 

Содержание PRK-8000





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды