manualshive.com logo in svg

Potec PRK-8000, Руководство по эксплуатации

Поделиться
Скачать
Potec PRK-8000 Скачать руководство пользователя страница 35

PRK-8000 Operation Manual

 

- 27 - 

6.3 Observe image obtained by Retroillumination

  

[ILLUM Mode]

   

 
By directing a light into the pupil, you can observe the condition of cataract or scratches on 
contact lens on the monitor in ILLUM Mode. 
Maximum of ten images for each eye can be displayed and stored in one display. When 
measuring more then 10 times, the oldest image is erased. 
You can select an image and display it in a magnified size. 
You can upload an image and display it in a magnified size to a computer. 

 

(1) Enter ILLUM mode. 

Press ILLUM button in the Measurement MODE. Press Exit button in order to go out 
ILLUM mode. 

 

[Freeze Mode Display] 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

[Freeze/Ref Mode Display] 

 

 

Press DISP button   
to enter menu display

Light for retroillumination reflected from retina 

End of the ILLUM Mode

Pupil 

change the amount 
of RETRO LED 

Sub. Number 

Light source 

Change the mode (“Freeze 

⇔

 Frz/Ref”)

Vertex distance

Light for eye front illumination reflected from cornea 

Press CLEAR button 
to clear the image 

change the amount
of Chart LED 

change the amount
of EXT-ILM LED

ON/OFF

RETRO LED

Содержание PRK-8000





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды