PoolPak ComPak AW 0550 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 92

background image

© 2017 PoolPak LLC. All rights reserved.

ComPak

®

Series - Installation, Operation and Maintenance |

49

ComPak

®

Series IOM

Status Screen 2 displays:
• Water Heating - YES or NO

• YES indicates that the unit is returning recovered heat back to the pool water.

• Aux Water Heat - YES or NO

• YES indicates that the controller has closed the relay contact requesting auxiliary pool water heater

operation.

• Water Temperature in °F or °C

Status Screen 3 displays:
• SPACE temperature control requirement:

•  TEMPERATURE- OK Indicates the space temperature is at setpoint.
•  HEATING- YES Indicates the space requires heating.
•  COOLING- YES Indicates the space requires cooling.

• AUX AIR HEAT- YES or NO Indicates the space requires additional heating. The auxiliary air heating relay

contacts close to activate the external heating system.

• DEHUMID (SURFACE) - YES or NO Indicates the space requires dehumidification. The word SURFACE

indicates that the unit is temporarily lowering the dew point set point to minimize condensation at the cold

surface temperature sensor.

• ECONOMIZER MODE- YES or NO Indicates the unit is cooling the space with outside air. ECONOMIZER

MODE is only shown if the optional economizer system is present.

Figure 5-4 Status Screen 4

Status Screen 4 displays the current system status as follows:

• Line 1: Day, Date and Time
• Line 2: Pool water flow status for units configured as full pool water heating. Possible text values include:

• Water Flow Normal
• Water Flow Too Low

• Line 3: Text relating the current active fault code. Possible text values include:

•  All systems normal
•  Unit is in OFF mode
•  Sys Startup Active
•  Fan Motor Overload
•  Fire Trip Active
•  Abnormal Space Temp
•  Defrost Switch Open
•  Cmpr Low Pressure
•  Cmpr High Mtr Temp
•  Cmpr High Pressure
•  Space T Sens Fail
•  Space RH Sens Fail Pool T Sens Fail
•  Outs T Sens Fail

«
...
47
48
49
50
51
...
»

Содержание ComPak AW 0550





























































































Отзывы:

Нет отзывов

Похожие инструкции для ComPak AW 0550

Бренд: castorama Страницы: 24

Бренд: ElectrIQ Страницы: 24

Бренд: ZOESURE Страницы: 16

Бренд: Holmes Страницы: 4

Бренд: Clean Air Optima Страницы: 10

Бренд: Clarke Страницы: 9

Бренд: Crane Страницы: 12

All Climate LAD250

Бренд: Breville Страницы: 16

Бренд: Topcom Страницы: 92

Бренд: Goldair Страницы: 5

Бренд: Goldair Страницы: 9

Бренд: Carel Страницы: 52

Бренд: Munters Страницы: 36

Бренд: Munters Страницы: 141

Бренд: Pneumatech Страницы: 20

Бренд: WC Wood Страницы: 3

Бренд: Madeira Страницы: 65

Бренд: Olimpia splendid Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды