POLTI vaporetto pro80, Инструкция по эксплуатации

Страница: 23 / 68

EN
G
LIS
H
| 23 |
8.5 Use the cloth previously steamed to clean the surface,
avoiding prolonged use on the same spot.
9. CLEANING BATHROOM FIXTURES,
GROUTING AND KITCHEN WORKTOPS
9.1 Make sure that Chapter 1 has been followed and connect the
accessories as indicated in Chapter 2.
9.2 Connect the concentrator accessory, equipped with bristly
round brush, to the hose. For the Pro90_Turbo model the steam
lance can be attached to the concentrator accessory. This is
recommended for reaching the most difficult-to-reach areas,
ideal for cleaning radiators, door and window frames,
bathrooms and shutters.
9.3 Adjust the intensity of the steam by turning the adjustment
knob (5); for this type of surface we recommend Maximum level
of steam.
9.4 Ensure that the steam lock on the handle is deactivated (6).
9.5 Press and hold the steam trigger on the steam hose (6) to
start cleaning.
10. OUT OF WATER
The lack of water in the boiler is identified by the out-of-water
light coming on (
).
To resume use, simply:
- switch off and disconnect the Vaporetto.
- fill the tank as described in Chapter 1.
- connect and turn the Vaporetto back on.
11. TURBO FUNCTION
only for the PRO90_TURBO model
When the TURBO function is active, the appliance adjusts to
the ideal steam pressure to remove the most stubborn dirt.
To activate the function, press the Turbo (9) button and wait
for the “ready steam” indicator light ( ) to turn off.
To deactivate the Turbo function, press the Turbo button again.
12. GENERAL MAINTENANCE
Before carrying out any maintenance on the device, always
unplug it from the power mains making sure that the product
has cooled down before proceeding.
To clean the outside of the appliance, only use a damp cloth
and tap water. All accessories can be cleaned using running
water, ensuring they are completely dry before the next use.
Do not use detergents of any type.
After using the brushes, we recommend letting the bristles cool
down in their natural position, in order to avoid any
deformation.
Periodically check the status of the coloured washer located in
the built-in socket and the connection seals of the extension
tubes and the steam hose. If necessary, replace with the
corresponding spare part, as described below.
13. KALSTOP
Kalstop is thelimescale product for appliances with boiler for
ironing and steam cleaning.
Regular use of Kalstop, every time the tank is filled with water:
- Extends the life of the appliance.
- Allows emission of a “drier” steam
- Prevents limescale build up.
- Protects the walls of the boiler.
- Contributes to saving energy.
HOW TO USE KALSTOP
13.1 Dilute one phial in 5 litres of water before putting it in the
tank.
13.2 Fill the tank as described in Chapter 1.
13.3 Proceed with the normal cleaning operations.
Kalstop is sold in packages of 20 phials at household appliance
stores, at Polti authorized service centres and at www.polti.com.
14. STORAGE
14.1 Turn off the appliance and disconnect from the mains
electricity.
14.2 Wait for the appliance to cool down completely before
storing it.
14.3 The hoses, brush and flexible hose can be housed on the
body of the appliance, sliding the hook on the floor brush into
the parking system on the appliance (11).
14.4 The extension tubes can be replaced in the special tube
holder compartment (12).
14.5 The small accessories can be placed in the accessories
compartment. To open the compartment, press gently on the
word “PUSH” (near the bottom of the lid), and open it (10).
For the Pro90_Turbo model the different coloured brushes
allow for a different colour for each surface or environment.
- Remove the damaged washer.
- Insert the new washer, attaching it on the
steam nozzle and pushing it into place.
- Lubricate the gasket with silicone grease
or Vaseline, or alternatively with small
quantities of vegetable oils.
WARNING: This operation must always be done after having
disconnected the appliance from the mains.
To connect the steam lance to the steam concentrator, simply
screw it on. The same operation can be carried out for the
brush, which can in turn be screwed onto the steam
concentrator and onto the steam lance.
VT PRO80-PRO90 - M0S11224 - 1P07:UNICO 06/08/2015 16.04 Pagina 23