22
6.
Crevice nozzle - 1 pc.
7.
Turbo brush – 1pc.
8.
User Manual 1 pc.
9.
Warranty Certificate 1 pc.
10.
Packing (plastic bag + box) 1 pc.
7. Operation
Open the box, carefully remove the device, release it from all packaging materials.
Connecting the hose:
Push the nozzle up into the air inlet until it clicks. Fig. 2
Disconnecting the hose:
Take the nozzle and unplug the device from the outlet.
Press the button to remove the hose nozzle from the socket.
Insert the tip of the hose handle into the fixed part of the telescopic tube. Fig. 3
Slide the plastic retainer on the fixed part of the telescopic tube forward (away from your boy) and pull the retractable part out to the desired length.
Adjust the telescopic tube length. Fig. 4
Put the necessary attachment on the retractable part of the telescopic tube (a large floor/carpet brush or a combined furniture/slot attachment). Fig. 5
Preparation of the attachment for cleaning carpets, tiles, and wooden covers: Fig. 6
Wall-to-wall carpeting – the brush is extended.
Hard coats – the brush is not extended.
Combined nozzles for cleaning curtains, furniture drapery, hard-to-reach places. Fig. 7
USE
1.Pull the cord to the desired length, wind the excess using the button.
Attention!
Do not pull the cord further than the yellow mark indicating that the approach of the unwinded cord end. The red mark indicates the unwinded cord end.
2.Connect the device to the power grid.
Attention!
Before connecting the device to the grid check that its technical specifications (see the “Technical Specifications” section) correspond to the grid parameters.
3. To turn on the device press the on/off button on the vacuum cleaner body.
Suction force adjustiment
4. You can adjust the suction force of your vacuum cleaner in two ways:
- using the air flow controller located on the hose handle. For delicate materials it is recommended to use minimum suction force. To do this open the regulator flap as
much as possible. When cleaning mattresses, furniture drapery and carpets, set the regulator flap to the middle position. When the regulator flap is closed the tile, the
wood, and other hard surfaces can be cleaned.
- with the help of the power control of the motor. The clockwise rotation of the regulator gradually increases the motor speed and the counterclockwise rotation
decreases it.
The suction force can be changed during the cleaning process.
5. Upon completion of work turn off the vacuum cleaner using the on/off button on the body, then unplug the device. To wind the cable press the automatic winding
button with one hand. Guide the cable with your other hand so that it reaches the receiver evenly.
CYCLONE DUST COLLECTION SYSTEM
The cyclone system does not require a dust collection bag. Dust particles are sucked into the dust collection bag by the air flow. The air is cleaned with a protective
filter installed at the outlet of the dust collection bag.
Warning!
Never use the device without a filter installed or if the filter is damaged or dirty. Otherwise the dust will get into the motor and cause the break of the
device.
If the filter blockage indicator lights up during operation turn off the device and clean the filters. Do not block the vacuum cleaner's air inlet.
8. Cleaning and storage
Dust collector cleaning
1.
Unplug the device and disconnect the power cord. Pull only the plug, not the cord. Fig. 8
2.
Remove the dust collection bag together with the cleaning system by pressing the lock button from the top to the bottom and pulling the container up by
the handle. Fig. 9
Attention: Never lift the vacuum cleaner by the handle of the container.
3.
Hold the container by the handle and place it over the garbage can with the bottom lid down. Press the button on the bottom cover of the container to open
and clear the dust. After removing the dust close the bottom cover.
4.
After cleaning the container remove the filters, rinse the container with the cold running water and wipe it dry or dry it thoroughly.
5.
Wash the filters with the warm water and dry them in a well-ventilated area.
Attention!
Do not wash the parts of the vacuum cleaner in a dishwasher or washing machine and do not dry them with a hair dryer or using heating devices.
6.
Insert the foam filter into the dust collector filter.
7.
Install the filter element body with filters on the dust collector.
8.
Fix the container to the body by inserting it into the body slot from top to bottom until it clicks. The device is ready for use.
9.
If the suction capacity has reduced but the container is not full yet open the container and see if something is blocking the filter screen. Please clean the
device when a blockage is detected.
Cleaning the air outlet HEPA filter
Before entering the atmosphere, the air is finally cleaned with a HEPA filter located on the back of the device. Clean this filter as follows: