Polaris 2010 OUTLAW 525 IRS Скачать руководство пользователя страница 60

Страница: 60 / 210

Features and Controls

Choke

The choke assists in starting a cold engine. The choke

knob is located on the left side of the carburetor. Refer

to the engine starting procedure on page 66 for correct

choke and throttle settings during starting.

Fuel Tank

The fuel tank filler cap is located directly below the

handlebar. Polaris recommends the use of 91 octane or

higher fuel.

Do not use fuel with ethanol content

greater than 10 percent, such as E-85 fuel.

Fuel Filters

The fuel pick-ups have internal fuel filters. Do not

attempt to clean the fuel filters. See your Polaris dealer

for service if you suspect the fuel filters are plugged.

Choke Knob

Содержание 2010 OUTLAW 525 IRS



















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 525 IRS, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды