Polaris 2010 OUTLAW 525 IRS Скачать руководство пользователя страница 151

Страница: 151 / 210

147

Maintenance

Toe Alignment

4. Measure the distance between the marks

and record the measurement (1).

5. Move the vehicle until the chalk marks

are at the rear of the tires, even with the

hub/axle center line.

6. Measure the distance between the marks

and record the measurement (2).

7. Subtract measurement 2 from measure-

ment 1. The difference is the vehicle toe

alignment.

8. The recommended toe alignment is 0" to

1/16" (0-1.6 mm) toe out. This means

that the front measurement should be 0" to 1/16" (0-1.5 mm) greater than the rear mea-

surement.

9. If you discover improper alignment, see your Polaris dealer for service.

Содержание 2010 OUTLAW 525 IRS



















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 525 IRS, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды