Polaris 2010 OUTLAW 525 IRS Скачать руководство пользователя страница 47

Страница: 47 / 210

Features and Controls

Clutch Fluid

The clutch fluid master cylinder is located on the

left handlebar. Check the fluid level in the reservoir

before each ride. The level should be 4mm below

the upper edge of the reservoir. Do not overfill.
Polaris recommends the use of KTM Hydraulic

Clutch Oil.

Do not use brake fluid. Do not mix

clutch fluid with any other hydraulic fluids.

See

page 170 for the part numbers of Polaris products.
1. Position the vehicle on a level surface.
2. Turn the handlebar until the master cylinder is

in a horizontal position.

3. Remove the two cover screws, the cover and the

rubber boot.

4. Add the recommended fluid as needed.
5. Reinstall the cover, boot and screws securely.

Screws

Cover

Boot

Содержание 2010 OUTLAW 525 IRS



















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 525 IRS, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды