Polaris 2010 OUTLAW 525 IRS Скачать руководство пользователя страница 162

Страница: 162 / 210

158

Maintenance

Rear Suspension

The rear suspension spring preload and shock compression

damping may be adjusted to suit different riding conditions

and operator weight.

Spring Preload

1. Raise and safely support the rear of the vehicle off the

ground to allow the suspension to fully extend.

2. Loosen the jam nut.
3. Turn the adjusting ring clockwise to increase preload.

Turn the ring counter-clockwise to decrease preload.

4. Tighten the jam nut firmly against the adjusting ring.
5. Measure the preload of the left and right shocks. Make

sure both shock measurements are equal.

Adjusting

Ring

(lower)

Jam Nut

(upper)

Increase

Preload

Decrease

Preload

Содержание 2010 OUTLAW 525 IRS



















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 525 IRS, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды