Polaris 2010 OUTLAW 525 IRS Скачать руководство пользователя страница 153

Страница: 153 / 210

149

Maintenance

Chain Tension

3. Tighten the pivot mounting bolts to 30

ft. lbs. (40 Nm).

4. Torque the chain adjusting bolt to 17

ft. lbs. (23 Nm).

5. Check sprocket bolts to make sure the

retainer tabs fit tightly against the bolt

heads. If not, tighten the bolts to 28 ft.

lbs. (38 Nm).

6. Bend the retaining tabs tightly against the flat edges of

the bolt heads. If a tab cannot be aligned with a flat

edge, it should be bent around a point of the bolt head.

TIP:

If a retainer tab does not align with the flat edge of a bolt

head, the bolt can be tightened to a maximum of 38 ft. lbs.

(51 Nm).

Proper splicelink clip

opening position

Содержание 2010 OUTLAW 525 IRS



















































































































































































































Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2010 OUTLAW 525 IRS, Руководство пользователя

Результаты поиска

Содержание 2010 OUTLAW 525 IRS

Отзывы:

Бренды по названию

Популярные бренды