Plug-In Solar Sheet Metal/Flat Roof Mount Kit Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 37

Plug-In Solar Sheet Metal/Flat Roof Mount Kit Скачать руководство пользователя страница 5

Plug-In Solar

289 London Road | Burgess Hill | West Sussex | RH15 9QU
www.pluginsolar.co.uk | [email protected] | 01444 672005

Page 5

SAFETY INSTRUCTIONS

Before installing or using a Plug-In Solar kit, please read all instructions and cautionary markings in
this document and on the Micro-Inverters and Solar Panels.

The installation of a Plug-In Solar kit shall be carried out by a competent person with sufficient skills

and  training  to  apply  safe  methods  of  work,  in  compliance  with  G83/2  Engineering
Recommendations.

The installation of a Plug-In Solar kit will be carried out to no lower a standard than that required in
the Manufacturer’s installation instructions, as provided here.

No parameter relating to the electrical connection and subject to type verification certification will
be modified unless previously agreed in writing between the DNO (Distribution Network Operator)
and the Customer.

All electrical installations shall be performed in accordance with local electrical codes.

All  appropriate  health  and  safety  regulations  must  be  observed  and  required  safety  precautions
taken.

Be aware that installation of this equipment includes the risk of electric shock.

Be aware that the body of the Micro-Inverter is the heat sink and can reach a temperature of 80°C.
To reduce risk of burns, do not touch the body of the Micro-Inverter.

DO  NOT  disconnect  the  PV  module  from  the  Micro-Inverter  without  first  disconnecting  the  AC
power.

!

In no circumstances, connect a DC input when an AC connector is unplugged.

DO NOT attempt to repair a Micro-Inverter. If it fails, contact APS Customer Support to obtain an
RMA number and start the replacement process. Damaging or opening a Micro-Inverter will void
the warranty.

CAUTION!

!

The external protective earthing conductor is connected to the micro-inverter

protective earthing terminal via an AC connector.

!

When connecting; connect the AC connectors

first  to  ensure  the  micro-inverter  earthing  then  undertake  the  DC  connections.  When
disconnecting;  disconnect  the  AC  by  opening  the  branch  circuit  breaker.  Whilst  maintaining  the
protective  earthing  conductor  in  the  branch  circuit  breaker,  connect  to  the  micro-inverter,  then
disconnect the DC inputs.

!

You MUST follow the IET Wiring Regulations at all times and consult a professional
electrician if you are in any doubt.

«
...
3
4
5
6
7
...
»

Содержание Sheet Metal/Flat Roof Mount Kit






































Отзывы:

Нет отзывов