Plug-In Solar Sheet Metal/Flat Roof Mount Kit Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 37

Plug-In Solar Sheet Metal/Flat Roof Mount Kit Скачать руководство пользователя страница 14

Plug-In Solar

289 London Road | Burgess Hill | West Sussex | RH15 9QU
www.pluginsolar.co.uk | [email protected] | 01444 672005

Page 14

WIRING THE SOLAR TO THE EXISITING MAINS CIRCUIT

IMPORTANT SAFETY INFORMATION – FOR YOUR PROTECTION

Before installation please read these instructions carefully and use the Plug-In Solar Connection Unit in
accordance with these safety wiring instructions.

In older houses, you may find a variety of old fuse boxes where the mains supply comes in. You may also
have wiring and fittings of an older style. These may not be up to the standard required today. If this is the
case, have it all checked and tested by a professional electrician BEFORE carrying out any work on it.
Some old installations may now be dangerous.

Electricity is dangerous. Always disconnect from mains supply before any inspection or repair to equipment.
Safety must always be given top priority. Do not allow children to tamper with electrical devices.

ALWAYS FOLLOW THE IET WIRING REGULATIONS.

You must NOT install the Plug-In Solar Connection Unit in the following locations as set out by Part P:

(a) within a room containing a bath or shower, the space surrounding a bath tap or shower head,
where the space extends —

(i) vertically from the finished floor level to —

(aa) a height of 2.25 metres; or

(bb) the position of the shower head where it is attached to a wall or ceiling at a point
higher than 2.25 metres from that level; and

(ii) horizontally —

(aa) where there is a bath tub or shower tray, from the edge of the bathtub or shower

tray to a distance of 0.6 metres; or

(bb) where there is no bath tub or shower tray, from the centre point of the shower

head where it is attached to the wall or ceiling to a distance of 1.2 metres; or

(b) a room containing a swimming pool or sauna heater.

As an additional precaution, wear rubber-soled shoes. This will provide a measure of insulation between you
and the ground!

IF YOU ARE NOT ABSOLUTELY CERTAIN ABOUT ANY ASPECT OF ELECTRICAL WORK, SEEK PROFESSIONAL ADVICE

1.1.

Switch off the power and remove the fuse for the relevant circuit before carrying out any

work, or inspecting, either it, or the appliances connected to it. Never inspect, or carry out work
on, any part of the system with the power on. Make sure that power cannot be inadvertently
restored by someone else.

1.2.

Use a voltage tester to check the power to the wires or connections are off before touching

them.

«
...
12
13
14
15
16
...
»

Содержание Sheet Metal/Flat Roof Mount Kit






































Отзывы:

Нет отзывов