Plextor PlexWriter 48/24/48A Скачать руководство пользователя | Manualshive

Страница: 25 / 56

background image

Section 2. Installing Your PlexWriter

PlexWriter 48/24/48A Installation and Users Manual

19

8. Double-check your work. You must ensure the side of the IDE cable with the red

stripe is matched to Pin 1 on the interface board and on the drive.

CAUTION: In the case of only one IDE device, you must make certain that one
end of the cable is always connected to the IDE connector on the motherboard.
The other end of the connector must be connected to a device. The end
connector of the cable should never be left unconnected.

9. Connect a power cable from the computer to the DC INPUT connector of the

PlexWriter drive. In most computers, you will find free power connectors that are
ready for your use.

Check the cable running from your power supply to your hard disk and see if it
has extra connectors on it. If so, you can plug one of these into the power
connector found on the rear panel of the PlexWriter.

Figure 16: Cable Connections for an Internal IDE PlexWriter Drive

10. Connect the analog audio cable if you want to use a sound board in your system.

This cable runs from the four-pin analog audio output connector on the rear panel
of your PlexWriter drive to your sound board. See “Using Sound Boards and
Audio Cables” below for more information about audio cables.

«
...
23
24
25
26
27
...
»

Содержание PlexWriter 48/24/48A

























































Отзывы:

Нет отзывов

Похожие инструкции для PlexWriter 48/24/48A

PowerXL DM1 Series

Бренд: Eaton Страницы: 28

Бренд: Eaton Страницы: 5

Бренд: Eaton Страницы: 240

Бренд: Eaton Страницы: 34

Бренд: Eaton Страницы: 179

Бренд: Eaton Страницы: 46

PowerXL DG1 Series VFD

Бренд: Eaton Страницы: 24

PowerXL DG1 Series VFD

Бренд: Eaton Страницы: 152

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 58

Бренд: Eaton Страницы: 20

Бренд: Eaton Страницы: 195

Cutler-Hammer SLX9000 Series

Бренд: Eaton Страницы: 24

PowerXL DM1 Series

Бренд: Eaton Страницы: 68

Бренд: Sumitomo Страницы: 50

Бренд: Geckodrive Страницы: 12

YSLO FLEX RTS 1P

Бренд: SOMFY Страницы: 28

Бренд: D+H Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды