Plextor PlexWriter 48/24/48A Скачать руководство пользователя | Manualshive

Страница: 26 / 56

background image

Section 2. Installing Your PlexWriter

20

PlexWriter 48/24/48A Installation and Users Manual

11. Connect a digital audio cable if your sound board is equipped with the

Sony/Philips digital interface (SPDIF) or Digital-In, and you wish to use the
digital audio output from your PlexWriter. This cable runs from the digital audio
output connector pins on the back panel to the sound board. (This cable is not
supplied by Plextor.)

12. Mount the PlexWriter drive in the computer using the four screws that were

supplied with your drive. Use only these screws.

CAUTION: Do not mount your drive in your computer using screws other than those
supplied by Plextor. You may damage the drive if you insert screws that are too long
or the wrong thread type.

Using Sound Boards and Audio Cables

Whichever category your sound board falls into, you will find that the best source of
information about installing the sound board in your computer is the board's manual.
Once you have successfully installed the sound board in your computer, you can
continue below for a description of the different cable connections that need to be
made.

Choosing and Connecting Audio Cables

If you do need audio cables, you will have to purchase them. Refer to the table
below. A list of several vendors who offer audio cables is available on Plextor’s web
site.

Audio Connection

Cable

Required

How to Connect It

MPC audio source

MPC-compliant
audio cable

Connect to MPC audio source,
and to analog audio output
connector at the rear of the
PlexWriter.

Sound Blaster or
compatible sound board

Sound Blaster-
compatible
analog audio
cable

Connect to Sound Blaster-
compatible audio board and to
analog audio output connector at
the rear of the PlexWriter.

Digital audio output

Cable that’s
compatible with
SPDIF or
Digital-In.

Connect to SPDIF or Digital-In
connector on sound board (if
sound board supports digital
audio) and to digital audio output
connector at the rear of the
PlexWriter.

«
...
24
25
26
27
28
...
»

Содержание PlexWriter 48/24/48A

























































Отзывы:

Нет отзывов

Похожие инструкции для PlexWriter 48/24/48A

1.5 24 A Series

Бренд: Lenze Страницы: 70

Бренд: Technodrive Страницы: 1

Бренд: Roland Страницы: 2

Бренд: Sprint Electric Страницы: 29

Бренд: MSI Страницы: 31

Бренд: Unimotion Страницы: 22

Бренд: LG Страницы: 2

Бренд: LG Страницы: 15

CED-8080B - - CD-RW Drive

Бренд: LG Страницы: 23

Бренд: LG Страницы: 22

Бренд: LG Страницы: 74

Бренд: LG Страницы: 2

FZ-VDR551 Series

Бренд: Panasonic Страницы: 4

FZ-VDM401 Series

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 17

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды