Planmeca Compact i3 Скачать руководство пользователя страница 99

Страница: 99 / 106

20 Resetting yearly maintenance counter

You must reset the yearly maintenance counter after dental unit installation.
A help message will remind the user about the yearly maintenance in

advance. The factory default is 30 days but you can change the number of

days in service mode 400.
Press the Program button and the About this unit button.

The

About this unit window appears.

Press > next to

Service to open the Service window with information for

service situations. In the

Service window, press > next to Yearly

Maintenance to access the following information:
•

When the yearly maintenance was last performed

•

How many days are left until the next yearly maintenance

The last item,

Confirm yearly maintenance, is for confirming that you have

successfully completed the yearly maintenance. Press > to display the

Confirm yearly maintenance window and enter the PIN-code 1701 when

prompted. Press OK to reset the yearly maintenance counter.

20 Resetting yearly maintenance counter

Installation manual

Planmeca Compact i3 95

Содержание Compact i3











































































































Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды

Planmeca Compact i3, Руководство по установке

Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды