Planmeca Compact i3 Скачать руководство пользователя страница 66

Страница: 66 / 106

3.c. Attach the Dürr contact to the suction element end of the suction

tube (3).

3.d. Attach the suction valve to the suction tube (5) and attach the

suction tube to the corresponding tube coming from the floor (7).

Secure the tubes into place with securing rings (4 and 6).

4. Install the assistant's syringe.

NOTE

The assistant's syringe is an optional feature.

4.a. Route the assistant syringe cable (1) and the assistant syringe

water and air tubes (2) from the opening for the suction element

through the lifting mechanism to the junction box.
In the lifting mechanism, the suction tube is placed on the upper

cable duct (2).
The assistant syringe quick-connector (4) will later be attached to

the suction element with two attachment screws (5), see step 5d.

4.b. Connect the assistant syringe cable to the Main control PCB (6).
4.c. Connect the assistant syringe air tube (2) to the air filter/regulator.
4.d. Connect the assistant syringe water tube (2) to the assistant

syringe valve.

12 Installing suction element

62 Planmeca Compact i3

Installation manual

Содержание Compact i3











































































































Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды

Planmeca Compact i3, Руководство по установке

Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды