manualshive.com logo in svg

Planet 8-Port IP Power Manager IPM-8001, Руководство пользователя, Страница: 41 / 58

Поделиться
Скачать
Planet 8-Port IP Power Manager IPM-8001 Скачать руководство пользователя страница 41

 

6.3.4 Trap 

Receivers 

This page lists the parameters for SNMP trap receivers (For SNMP Network Management). 

 

 

Option 

Description 

Index

 

The index number of the entry in the table. 

NMS IP Address 

The IP Address in dotted format of the NMS station to which the trap 

should be sent. 

Community String 

The community string of the trap PDU to be sent. The maximum 

length of the string is 19 characters. 

Trap Type 

Types of the traps to be received. Set the type of the trap. 

[None]: Traps are not be received. 

[IP Power Manager Trap]: Traps are received base on IP Power 

Manager MIB. 

Severity 

Set the level of the trap to be received. 

[Information]: All traps are received. 

[Warning]: Trap that need to be noticed and are in dangerous is 

received. 

[Severe]: The significant traps such as the outlet voltage over 

threshold are received. 

Description 

Customer description string. 

- 27 -

 

 

 

 

Содержание 8-Port IP Power Manager IPM-8001



























































Отзывы:

Нет отзывов