Planet 8-Port IP Power Manager IPM-8001 Скачать руководство пользователя страница 11

Страница: 11 / 58

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information

about the IP Power Manager.

2.1

Connecting Input Power

The IP Power Manager has an IEC C20 power inlet for supplying and managing power for the

output devices. Connect the power cord to the power inlet and plug the other end into a power

outlet as shown:

After power connected. You may see the 7-Segment LED display some error messages. If it

shows “

E01

”, please refer to section 2.6 to connect IP Power Manager 8000 to your LAN or

WAN. If it shows “

E16

”, that is mean the power phase of connected power outlet is reverse.

Please try to make the power phase correct. Or you can refer to section 5.2.2 to disable

Input Phase Detection on IP Power Manager temporally. For other error message, please

refer to Appendix A Error Code for details.

2.2

Connecting Output Device

- 6 -

The IP Power Manager has eight power outlets for connecting devices such as workstations,

servers, and printers. Their power on/off status can be controlled manually as well as

remotely through the LAN and Console ports. Connect the power connectors of the devices

to each of the power outlets A through H with the power cords supplied with the devices as

shown:

Содержание 8-Port IP Power Manager IPM-8001



























































Результаты поиска

Содержание 8-Port IP Power Manager IPM-8001

Отзывы:

Planet 8-Port IP Power Manager IPM-8001, Руководство пользователя, Страница: 11 / 58

Результаты поиска

Содержание 8-Port IP Power Manager IPM-8001

Отзывы: