Planet 8-Port IP Power Manager IPM-8001 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 58

Planet 8-Port IP Power Manager IPM-8001 Скачать руководство пользователя страница 12

2.3

Connecting Digital Outputs

The IP Power Manager provides two digital outputs (NO by default) to which you can

connect indicators or other output devices that are normally open (NO) or normally closed

(NC). The digital output connectors are work as a switch to let you switch the connected

device On or Off. The connectors will not provide power to the connected device. So the

connected device should connect with its power adapter. You can control the digital outputs

remotely through the console or over the LAN.

2.4 Connecting

EMD

- 7 -

An environmental monitoring device that is sensors connected to for detecting temperature,

humidity, water level, and so on can be connected to the IP Power Manager with the console

port. The EMD can also be connected to alarms or indicators and controlled through the IP

Power Manager. Connect the EMD to the console port as shown:

«
...
10
11
12
13
14
...
»

Содержание 8-Port IP Power Manager IPM-8001



























































Отзывы:

Нет отзывов