Planet Networking & Communication WDRT-730 Скачать руководство пользователя

Страница: 42 / 105

User Manual of WDRT-730

-35-

Provider

Select your DDNS service provider here.

Domain Name

Input the domain name you’ve obtained from DDNS service provider.

Account / Email

Input account or email of DDNS registration.

Password / Key

Input DDNS service password or key.

Table 5-9

5.2.2.9.

WISP

If your Internet connection provided by your local ISP is through wireless network, please select this

mode. After you have connected the router to the access point of the ISP wirelessly, please setup the

WAN connection type in WAN page.

Figure 5-17

Object

Description

Disable / Enable

/ Enable (Station Mode

Only)

Disable: disable WISP function.

Enable: enable WISP function and the router can also act as an access

point for the wireless clients to associate to it for Internet connection.

If you are informed by your local ISP that the wireless
settings of the access point is changed, please configure the
router in this page for matching the new settings.

Enable (Station Mode Only): enable this function and the router will act

Содержание WDRT-730










































































































Результаты поиска

Содержание WDRT-730

Отзывы:

Похожие инструкции для WDRT-730

Бренды по названию

Популярные бренды

Planet Networking & Communication WDRT-730, Руководство пользователя

Результаты поиска

Содержание WDRT-730

Отзывы:

Похожие инструкции для WDRT-730

Бренды по названию

Популярные бренды